Arc Blow in Stud Welding: Causes, Signs and Fixes

by | Nov 12, 2026 | 0 comments

A good drawn arc stud weld finishes with a full, even fillet all the way around the base of the stud. When the fillet piles up on one side and thins out or disappears on the other, arc blow is a likely cause.

Arc blow is easy to mistake for a bad stud, a worn gun or the wrong settings. In many cases the fix is simpler: change the ground.

What Arc Blow Is

Arc blow is the sideways push of a magnetic field on a welding arc. ESAB notes that it is most common on ferromagnetic steels welded with DC current, and often worst at the ends of joints and at corners.

Drawn arc stud welding runs on DC current and holds the arc long enough to melt the end of the stud and a pool in the base metal. If the magnetic field around that arc is lopsided, it pushes the arc off centre, and the molten metal goes with it.

Why It Happens in Stud Welding

Welding current runs down through the stud, turns sharply into the work and travels back to the machine through the ground clamp. A final research report prepared for AISC by LeTourneau University explains that this turn crowds the magnetic field on one side of the arc and spreads it thin on the other. The arc is driven toward the far side of the current return path. The researchers could produce arc blow on purpose simply by grounding the part on one side only.

Common triggers include:

  • One ground clamp placed off to one side or far from the weld.
  • Welding near the edge or end of a plate, where current and field lines crowd together.
  • Heavy steel on one side of the stud, such as stiffeners, flanges or fixtures.
  • Residual magnetism left in the part by magnetic lifting or earlier processing.
  • Coiled or looped welding cable lying near the work.

How to Spot Arc Blow on a Stud Weld

  • The fillet is heavy on one side and thin, undercut or missing on the other.
  • The thin side points the same way on stud after stud.
  • The pattern shifts when the ground moves, or when welding near an edge.
  • Bend or torque tests fail in the weld instead of the stud.

A handy check: the heavy side of the fillet tends to form on the side of the stud away from the ground. A US patent on stud welding ferrules describes this pattern, and it matches the research above. If the heavy side faces away from the ground clamp, arc blow is a strong suspect.

Arc blow is not just cosmetic. The AISC report describes it as the culprit behind a significant portion of drawn arc stud weld failures, because it leaves incomplete fusion across the weld. A sound weld shows a full and even flash all the way around and, when tested to destruction, will most likely break in the stud shank rather than the weld.

How to Fix Arc Blow

Start with the ground. ESAB lists return clamp placement as the fastest and lowest cost fix, and the AISC report ranks symmetrical ground placement as its most important recommendation.

  1. Use two ground clamps, balanced. Place them on opposite sides of the weld area at similar distances so their fields offset each other.
  2. Move the ground. With only one clamp, try different positions and watch which way the fillet shifts.
  3. Clamp to clean metal. Full jaw contact on bare, clean metal matters. Paint, rust or a loose clamp add resistance and make the arc less stable.
  4. Keep cables straight. Avoid coils and loops of welding cable near the work.
  5. Plan the sequence. On long parts, move the ground as welding progresses, and pay extra attention to studs near edges, ends and heavy sections.
  6. Check for residual magnetism. If the fillet leans the same way no matter where the ground goes, the part itself may be magnetized. A gaussmeter can confirm it, and the part may need demagnetizing.
  7. Retest after each change. Weld a test stud, inspect the fillet and run a bend check before going back to production.

Grounding basics are also covered in Mastering Stud Weld Quality: A Comprehensive Troubleshooting Guide, and drawn arc setup in How to Make Clean Welds With Drawn Arc Stud Welders. Ferrule choice and condition matter too, as explained in Understanding Ferrules.

Does Arc Blow Affect CD Stud Welding?

Arc blow is mainly a drawn arc concern. The AISC report notes that arc blow problems grow with longer weld times, because magnetic fields need time to build. CD welds are over in milliseconds. Even so, clean and solid grounding matters for consistent results on any stud welder.

Arc Blow FAQ

What is arc blow in stud welding?
A magnetic field pushing the arc to one side, which leaves an uneven fillet around the stud.

What causes arc blow?
Usually an uneven current path: a single ground off to one side, welding near plate edges, heavy steel nearby or a magnetized part.

What is the quickest fix for arc blow?
Balance the ground. Use two ground clamps on clean metal, placed evenly on opposite sides of the weld area.

Does arc blow weaken a stud weld?
Yes. It can leave incomplete fusion on one side of the stud.

Is arc blow a problem with CD stud welding?
It is mainly a drawn arc issue, since arc blow builds with longer weld times and CD welds finish in milliseconds. Good grounding still matters.

Get Help With Uneven Stud Welds

Fighting lopsided fillets or inconsistent welds? Davis Stud Welding provides technical support after purchase, plus setup and operator training on its equipment depending on location, as outlined on the Davis FAQ page. Call 1 (855) 720-2977 or contact the team.

Sources